Cart

What is This Part?

• These are the CONE WASHERS that fit onto the Locking Hub Installation Bolts.
• INCLUDES One Full Set of Cone Washers (Does One Locking Hub - RH or LH)
• Direct Replacement

What Will I Receive?

• Qty 6 - Cone Washers (Does One Locking Hub - RH or LH)

What Vehicle Will This Fit?

• Suzuki Samurai       1985 - 1995        All Models
• Suzuki SJ413           1985 - 1995       All Models
• Suzuki SJ410           1980 - 1984       All Models

General Information NEW in the Original Packaging Stocked & Shipped From – LEXINGTON, KY What is This Part? These are the Suzuki Samurai OEM Flexible Wire Clamps. These are the Original Suzuki Rubber Coated Flex Clamps. Bolt-On Design. Bends to Any Shape Required. Best Clamp Made for Holding Wires and Cables Securely in Place. Doesn’t Damage...

General Information NEW in the Original Packaging Stocked & Shipped From – LEXINGTON, KY What is This Part? These are Axle Grease Caps that fit a wide array of Vehicle Make and Models. Made from 1.5mm Thick Steel Cap Shaft is 40mm Wide Cap Flange is 49mm Wide Cap Height is 20mm Direct Replacement What...

General Information

• NEW in the Original Packaging
• Stocked & Shipped From - LEXINGTON, KY

What is This Part?

• This part is the Lug Nut Stud that fits into the Drum and receives the lug nut after the wheel has been mounted.
• Does Both Rear Wheels
• These are "Clipped" Studs for the REAR wheels on the 1980 - 1987 Models
• FINISH: Zinc
• OEM - Made by SUZUKI

What Will I Receive?

• Qty 10 - Lug Nut Studs (Rear Wheels)

What Vehicle Will This Fit?

• Suzuki Samurai      1988 - 1987       All Models
• Suzuki SJ410           1980 - 1984       All Models

General Information

• NEW in the Original Packaging - (Unless Bulk Packed)
• OEM - Made by SUZUKI
• Stocked & Shipped From - LEXINGTON, KY

What is This Part?

• This part is the Lug Nut Stud that fits into the Drum and receives the lug nut after the wheel has been mounted.
• It is part number 09119-12006.
• To replace all studs it requires 5 studs per drum.
• These are for the REAR wheels only.
• The front wheels require a different type stud part #09119-12008, which we also sell.
• To purchase that item select the “Wheels/Spare Tire” Category in the far left column.
• Note: Color May vary

What Will I Receive?

• Qty 10 - Lug Nut Studs (Rear Wheel)

What Vehicle Will This Fit?

• Suzuki Samurai      1988 - 1995       All Models
• Suzuki SJ413           1988 - 1995       All Models

What is This Part?

• This part is the Suzuki OEM Lug Nut Stud that fits into the Front Rotor and receives the lug nut after the wheel has been mounted.
• It is part number 09119-12008.
• To replace all studs it requires 5 studs per rotor.
• These are for the front wheels only.
• The rear wheels requires stud #09119-12006, which we also sell.
• To purchase that item select the “Wheels/Spare Tire” Category in the far left column.
• NOTE: THESE WHEEL STUDS ARE THE NON-CLIPPED HEAD. The 1986 - 1988 have a clipped head. This changed occurred in the late 88 thru early 89 models so please verify which type you need if you are ordering for an 88' or 89' Samurai. From the 90' model Samurai on to 95’ they were all Non-Clipped.
• ALSO INCLUDED: Lug Nuts for the Front Wheel Studs!

What Will I Receive?

• Qty 10 - Front Studs
• Qty 10 - Lug Nuts

What Vehicle Will This Fit?

• Suzuki Samurai      1985 - 1995       All Models
• Suzuki SJ413           1985 - 1995       All Models